224
National Instruments • T
el: (800) 433-3488
•
Fax: (512) 683-9300
•
[email protected] •
ni.com
Multifunction DAQ Accessories
DAQ and Signal Conditioning
Multifunction DAQ Accessories
Figure 9. TBX-68 I/O Connector Block
Figure 8. SCB-68 and SCB-100 Shielded I/O Connector Blocks
Figure 7. TB-2705 Terminal Block
BNC-2090 Shielded BNC Adapter Chassis (see Figure 5)
The BNC-2090 is a shielded, rack-mountable adapter with signal-labeled BNC
connectors, spring terminal blocks, and component locations for passive signal
conditioning. Consists of 22 BNC connectors and 28 spring terminals to simplify
connection to your analog, digital, trigger and counter/timer signals. The BNC-2090
has silk-screened component locations that you use to develop simple signal
conditioning circuits. For added flexibility, you can connect any E Series DAQ device
to the BNC-2090 from the front or rear through dual 68-pin connectors.
BNC-2090 .............................................................................................777270-01
Dimensions – 48.3 by 4.4 by 18.8 cm (19.0 by 1.7 by 7.4 in.)
CA-1000 Configurable Signal Conditioning Enclosure (see Figure 6)
The CA-1000 is a configurable enclosure that gives you maximum user-defined
connectivity and flexibility through customized panelettes. Each enclosure can
accommodate up to nine panelettes.
Dimensions – 30.7 by 25.4 by 4.3 cm (21.1 by 10 by 1.7 in.)
See page 352 for more information about the CA-1000.
TB-2705 Terminal Block for 68-pin PXI E Series Devices (see Figure 7)
The TB-2705 is a screw terminal block for PXI that works with your PXI
E Series DAQ module. It latches to the front of your PXI module with locking
screws and provides strain relief and easy access to your analog, digital, trigger
and counter/timer signals through screw terminals.
TB-2705 ................................................................................................778241-01
Dimensions – 8.43 by 10.41 by 2.03 cm (3.32 by 4.1 by 0.8 in.)
SCB-68 and SCB-100 Shielded I/O Connector Blocks (see Figure 8)
The SCB-68 and SCB-100 are shielded I/O connector blocks for rugged, very low-
noise signal termination for connecting to 68-pin or 100-pin E Series DAQ devices,
respectively. Silk-screened component locations for easy addition of simple
signal-conditioning circuitry for your analog input channels. They also include
general-purpose breadboard areas (two on the SCB-68; three on the SCB-100) as
well as an IC temperature sensor for cold-junction compensation in temperature
measurements.
SCB-68 ..................................................................................................776844-01
Dimensions – 19.5 by 15.2 by 4.5 cm (7.7 by 6.0 by 1.8 in.)
SCB-100 ................................................................................................776990-01
Dimensions – 19.5 by 15.2 by 4.5 cm (7.7 by 6.0 by 1.8 in.)
TBX-68 I/O Connector Block with DIN-Rail Mounting (see Figure 9)
The TBX-68 is a termination accessory with 68 screw terminals for easy
connection of field I/O signals to 68-pin DAQ devices. It includes one 68-pin male
connector for direct connection to 68-pin cables. The TBX-68 is mounted in a
protective plastic base with hardware for mounting on a standard DIN rail.
TBX-68 ..................................................................................................777141-01
Dimensions – 12.50 by 10.74 cm (4.92 by 4.23 in.)
Figure 6. CA-1000 Configurable Signal Conditioning Enclosure
Figure 5. BNC-2090 Shielded BNC Adapter Chassis
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales