DAQ VXI-SC-1102 Manual de instrucciones Pagina 101
- Pagina / 151
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 15 VXI-DAQ Devices
©
National Instruments Corporation 15-3 DAQ Hardware Overview Guide
values for all the analog output channels. All analog channels are
guaranteed to be at their power-on values 5 ms after deassertion of system
reset.
VXI-AO-48XDC Digital I/O
The VXI-AO-48XDC contains 32 lines of digital I/O. These lines are
divided into four ports of 8 lines each. These four ports are referred to as
ports 0 through 3 by the digital I/O functions. You can program each of
these ports on a line basis; you can configure each line individually for
input or output. In addition, each line that you configure as an output line
has read-back capability (that is, by reading the port associated with a
particular line, you can determine what digital value the output line is
currently asserting). These digital I/O ports operate only in nonlatched
mode.
VXI-MIO-64E-1 and VXI-MIO-64XE-10
Multifunction VXIbus Devices
The VXI-MIO Series includes the following modules:
• VXI-MIO-64E-1
• VXI-MIO-64XE-10
The VXI-MIO Series modules are high-performance multifunction analog,
digital, and timing I/O modules for VXIbus.
This family of modules features 12-bit and 16-bit ADCs with 64 analog
inputs, 12-bit and 16-bit DACs with voltage outputs, eight lines of
TTL-compatible digital I/O, and two 24-bit counter/timers for timing I/O.
The VXI-MIO Series modules use the National Instruments DAQ-STC
system timing controller for timer-related functions. The DAQ-STC
consists of three timing groups that control analog input, analog output, and
general-purpose counter/timer functions. These groups include a total of
seven 24-bit and three 16-bit counters and a maximum timing resolution of
50 ns.
A common problem with other VXI modules is that you cannot easily
synchronize several measurement functions to a common trigger or timing
event. The VXI-MIO Series modules solve this problem by using VXIbus
triggers to synchronize measurements on several VXI-MIO Series
modules.
- DAQ Hardware Overview 1
- Important Information 3
- Chapter 14 7
- SCXI Hardware 7
- Glossary 10
- Contents 11
- About This Guide 12
- MIO and AI Device Terminology 15
- Table 1 16
- Related Documentation 17
- MIO and AI Devices 18
- Chapter 1 MIO and AI Devices 19
- E Series Data Acquisition 20
- Set_DAQ_Device_Info 22
- MIO Device Analog Output 24
- E Series Digital I/O 26
- E Series PFI Pins 27
- Lab and 1200 Devices 28
- AI_Trigger_Config.vi 31
- DAQ_StopTrigger_Config 31
- Table 2-2 32
- Lab and 1200 Devices Groups 33
- Figure 2-1 34
- 1200 Device Acquisition Rate 35
- 1200 Device Calibration 36
- LPM Devices 37
- DAQ_Config 38
- LPM Device Digital I/O 39
- LPM Device Counter/Timers 40
- 516 Devices and 41
- DAQCard-500/700 Devices 41
- DAQ_Config. If you do 43
- Counter/Timer Operation 44
- Figure 4-2 45
- AT-AO-6/10 Analog 46
- Output Devices 46
- AT-AO-6/10 Digital I/O 48
- 6703/6704 Devices 49
- PC-TIO-10 Timing I/O Device 50
- PC-TIO-10 Counter/Timers 54
- PC-TIO-10 Digital I/O 55
- DIO-96 Digital I/O Devices 56
- DIO-96 Groups 57
- DIO-24 (6503) 58
- AT-MIO-16DE-10, and 6025E 58
- DIO-32F and 6533 60
- Digital I/O Devices 60
- Digital_Buffer_Write.vi) 62
- AMUX-64T External 63
- Multiplexer Accessory 63
- Table 11-2 64
- AMUX-64T Channel Numbers 64
- SCAN_Setup or 65
- MIO_Config 67
- Accessories 68
- SC-2042-RTD Accessory 69
- SC-2043-SG Accessory 69
- SCC Series Modules 70
- SCC-CI20 Current Input Module 72
- SCC-LP Lowpass Filter Modules 73
- SCC Configuration 74
- SCXI Operating Modes 76
- Chapter 14 SCXI Hardware 77
- SCXI Data Acquisition Device 80
- SCXI-1200 80
- SCXI Analog Input Modules 81
- SCXI-1100 81
- SCXI-1101 82
- SCXI-1104/C 83
- SCXI-1112 83
- SCXI_Scale function to 84
- SCXI_Single_Chan_Setup 84
- SCXI-1125 85
- SCXI-1122 85
- SCXI-1126 86
- SCXI-1127 87
- SCXI-1140 87
- SCXI Analog Output Module 89
- SCXI-1124 89
- SCXI Digital Modules 90
- SCXI-1160 and SCXI-1161 90
- SCXI-1162 and SCXI-1162HV 91
- SCXI-1163 and SCXI-1163R 91
- SCXI-1530, SCXI-1531 92
- SCXI-1540 92
- SCXI_Track_Hold_Setup 94
- DIO-24 and the DIO-96 96
- DIO-32F and 6533 Device 97
- VXI-DAQ Devices 99
- AO_Change_Parameter or the 100
- Multifunction VXIbus Devices 101
- VXI-DAQ Signal Conditioning 102
- VXI-SC-1102 Submodule 103
- VXI-SC-1150 Submodule 103
- PXI DAQ Devices 104
- PXI DAQ Signal Conditioning 105
- NI 5411 Devices 106
- Chapter 17 NI 5411 Devices 107
- DDS Mode 108
- Table 17-2 110
- NI 5411 Operational Modes 110
- Device Analog Input 112
- Data Acquisition 113
- Acquisition Timing 114
- Current Source 115
- Digital I/O 115
- Device Input 116
- Chapter 19 NI 40XX Devices 118
- DSA Devices 119
- and NI 455 120
- Analog Input Channels 120
- Data Acquisition Timing 121
- Channels 122
- Digital I/O 123
- Counter/Timer Operation 124
- Devices 125
- Chapter 21 671X Devices 126
- Technical Support Resources 129
- Worldwide Support 130
- Numbers/Symbols 131
Relacionado con productos y manuales para Amplificadores de audio DAQ VXI-SC-1102
(57 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.102 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales